[Nirmala Shenoy]

hello Komal,

the script is not working. I was unable to get back the assigned addresses. if there is some solution to this problem that would be very helpful

thanks

 

[Nirmala Shenoy]

I tried with configure and validate – it gave the following repsonse

User: nxsvks@rit.edu bastion key is valid!
Bastion SSH Config file already exists, not making updates!
Configuration is valid and please save the config!
I am assuming that the config was saved ( not sure how to do it)
I tried reserving again and got the same error

Post boot config node_name, Failed! for all nodes

[Nirmala Shenoy]

Hello

I used the configure.ipynb from jupyter-examples-rel1.6.0.

the requirements .txt shows

fabrictestbed-extensions==1.6.0
python-dotenv
ipython==8.12.0
fabrictestbed-mflib>=1.0.4

pip install uses this requirements file. 

The version before this shows 1.5.4. 

[Nirmala Shenoy]

hello I am attaching a snap shot. when I run tshark in the home directory I get a permission denied. If I save a text file it works

When I run it in my code directory – I am able to save.

attached is the error capture

[Nirmala Shenoy]

hello just checked I am using the default option fablib 1.5.4.

using the same  container as my student

[Nirmala Shenoy]

Hello am sending as two snapshots

[Nirmala Shenoy]

Problem with txt file also. I am attaching to snapshots of the slicebuilder notebook

[Nirmala Shenoy]

sorry did not like the upload file format. here is the txt

[Nirmala Shenoy]

here is the ipynb.

Both my students executed this book and did not have a problem.

 

 

[Nirmala Shenoy]

Hello I am attaching the snapshot from the slice reservation. as noticed the process is hanging – some slivers are ticketed. from the retry  20 and time 433 seconds I think there has been no update for quite some time (was in a faculty meeting for the last 1.30 hours).

the cell instructions you provided I added it after the slice reservation. But because the previous cell (i.e. the reservation was not completed) I think it is not able to execute this cell.

I changed the slice_name variable

[Nirmala Shenoy]

I tried executing a cell with

slice = fablib.get_slice(name=slice_name)
slice.show()
slice.list_nodes()
slice.list_networks()

but did not get any output.

I have a new slice with ID c5eff2e0-8162-4d10-bcec-1ffd17b03698. it is named eibp2. on the portal it says Stable OK. but I am again struck at the same place as before. some resources still show up as ticketed.

 

 

[Nirmala Shenoy]

Hello – this is the slice that I reserved, where it says that the slice is stable OK but the cell is stuck at the screen shot I sent earlier. I am attaching a screenshot before the extension.

[Nirmala Shenoy]

Hello

just reserved a slice named EIBP. SliceID c4f9b90e-fd19-4cb6-b1b1-d53e89471881.

it is showing that it is configuring, but when I check at the portal – it says that the slice is table OK. when I tried to extend the lease end – it says lease end time is not in format … failed to renew the slice.

The configuration is not completed – so I do not have access to the nodes i.e. the ssh commands to connect to the nodes. attaching a snapshot of the slice reservation process that is hanging.

 

 

[Nirmala Shenoy]

Hello

the slices I was trying to reserve was under the project titled Expedited Internet Bypass Protocol. Unfortunately as I could not reserve any slice, I cannot provide the slice ID.

Regarding the styler warning – I noticed that happening with my student Kriti – but she was able to reserve the slice. Unfortunately I could not. I redid my configuration incase I had an outdated conf. file. But still was not successful after seven eight attempts. It is affecting my project progress. Given that I do not have the sliceID I am not sure how to get this resolved.

[Author]

Posts